欧美免费全部免费观看

    <tr id="xd0ew"></tr>

  1. <center id="xd0ew"><em id="xd0ew"></em></center>
  2. <big id="xd0ew"><em id="xd0ew"></em></big>
    <big id="xd0ew"><em id="xd0ew"></em></big>

    1. Amazing Machinery, Your Equipment Superstore Since 1995
      Professional Jetter Business Package

      Sewer Jetter FAQ

      What is sewer jetting?

      Sewer Jetting is the application of directed high pressure water to remove clogs, dirt, grease, and/or grime from pipes to allow them to flow freely. A Pump, along with a jetter tip to create restriction, is used to generate a pressure in some cases powerful enough to cut through concrete. Sewer Jetting is a valuable means of cleaning interior pipe surfaces at incredible speeds.

      Which Sewer Jetter should I buy?

      We sell a wide variety of Sewer Jetters, accessories and parts. The easiest thing to do is call us toll free at 1-800-504-7435 and tell us your situation. We'll help you pick out the right model for your needs and budget.

      What’s more important, pressure (PSI) or water volume (GPM)?

      Both PSI and GPM are very important for the optimum performance from a sewer jetter. The pressure lifts the dirt and the water volume carries it away.

      What do I do with my machine in the winter?

      If you live in a climate where it is below freezing you will want to run pump saver antifreeze through your system before putting it to bed at night. When using auto antifreeze the mixture should be 50/50 antifreeze and water. The ideal condition is to store your machine in a climate controlled building but not all of us can do that.

      How do I run the antifreeze mixture into my machine?

      For a cart mounted machine try these simple steps. Using an old garden hose cut off the end with the male thread remaining in about a two to three foot section. Using a funnel insert it into the cut end and funnel pump saver antifreeze or a 50/50 mixture auto antifreeze/water through the pump by pulling the rope start several times until the mixture comes out the other end of the jetter hose. Be sure to drain water from all non-pressurized hoses on your machine to prevent freezing.

      For a truck or trailer mounted rig you may add a secondary tank with a capacity of 25-50 gallons, and have it plumbed to your supply line like your regular water tank with ball valves to control the flow. Allow the antifreeze mixture to flow through the high-pressure system and with your jetter tip back into the smaller tank it will recycle its self. You will have to change the antifreeze from time to time, as the mixture will become too diluted. Be sure to drain water from all non-pressurized hoses and tanks on your rig to prevent freezing.

      Should I remove the fuel from the tank when storing my sewer jetter?

      For safety reasons it's always best to remove the fuel for storage. If you do not plan on storing for longer than a month you can use a stabilizer. You should never store gas inside your home.

      How much sewer jetter hose can I use?

      Using 1/4" jetter hose, the recommended max length is 150' however you can run more. If you choose to use over 150' you may find the hose is not pulling as well into the pipe. On larger machines using 3/8" or 1/2" jetter hose, the recommend max length is 300'.

      What do the different Jetter nozzles do?

      Laser Nozzle or Penetrator Nozzle
      Cuts, Dislodges and Flushes blockages
      One Forward Jet, Three Backward Jets

      Ram Nozzle
      Rams and Flushes tougher debris
      Three Backward Jets

      Impactor Nozzle
      Moves sand, grit and light scale which may have accumulated within the line
      One Forward Jet, Three Sideward Jets, Six Backwards Jets

      Rotating Nozzle or Spin-Jet Nozzle
      Polishes and maximizes line recovery
      Two Side Facing Jets, 2 Backward Jets

      Flusher Nozzle
      Flushes loose debris
      Six Backward Jets

      De-Icer/De-Greaser Nozzle
      Removal of heavily blocked lines with grease, hard soap or even ice
      Three Forward Angle Jets, Six Backward Jets

      Cornering Nozzle
      Navigates around P-Traps and tight bends
      One Forward Jet, One Sideward Jet, Three Backwards Jets

      How do I clean a clogged nozzle?
      Remove the nozzle from your system Using our Nozzle Cleaner or a small piece of wire like a paper clip clear the clog. Flush water backwards through the nozzle and replace it on your sewer jetter. If it is still partially clogged, try again.

      How often should I replace my nozzles?

      This depends on much time you use your machine. A good rule of thumb is if you notice a gradual pressure lose you should replace that tip. Not all tips will wear out at the same time.

      Why should I keep my nozzles clean?

      A clogged nozzle will not clean as well and can increase the back pressure on your pump causing damage.

      What type of oil do I use in my pump?

      You want to use Non-detergent oil. You should always refer to your owner's manual to understand what type Non-detergent oil the manufacturer recommends.

      I have a hot water supply outside, can I run this through my pump?

      No, incoming hot water can damage your pumps seals. Our pumps have a max inlet Water temperature of 80 degrees with a max pump temperature of 140 degrees. If your pump exceeds 140 degrees the thermal relief valve will pop to protect your pump and it will need to be replaced. However you can add an optional Hot Pump Upgrade to most of our machines that will give you a max inlet water temperature of 140 degrees with a max pump temperature of 190 degrees to be used with hot inlet water.

      What does by-pass mean?

      This allows the pump to circulate water so there is no pressure build up however if you leave your machine in the by-pass mode for longer than two minutes you risk overheating your pumps. We use a thermal relief valve to stop this from happening.

      What is a thermal relief valve?

      This is a safety feature for your pump. It will keep the pump from burning up if left in the by-pass mode for too long. This valve is set to the max pump temperature rating. If the valve pops you will need to replace it.

      If you were not able to find the answer you were looking for in this section, call Amazing Machinery at 1-800-504-7435 to speak with one of our experienced Jetting Staff Members.

      ORDER TODAY! 1-800-504-7435
      Amazing Machinery Logo
      We accept credit cards and Paypal Lease This Jetter OAC

      Home | Contact Us | Site Index | LinksJetter FAQArticles | Testimonials | Terms of Use | Privacy

      Proposition 65: Information, required to show to our customers in California Follow us on Facebook Secure Website Amazing Machinery, LLC BBB Business Review


      Plumbing & Contractor's Equipment since 1995

      Sewer Cameras
      Viztrac
      Forbest
      Ridgid
      General Wire
      Opticam
      Electric Eel
      Wohler
      Locators - Line & Sonde

      Sewer Jetters
      BossJet Sewer Jetters
      Ridgid Sewer Jetters
      General Sewer Jetters
      Trailer Sewer Jetters
      Hot Water Jetters
      Jetter Conversion Kits
      Jetter Hoses
      Jetter Nozzles
      Nozzle Calculator

      Cable Machines & Cables
      Valor
      Ridgid
      Milwaukee
      Torque Master
      General Wire
      Steel Dragon
      Electric Eel
      Replacement Cables

      Plumbing Machinery
      Plumbing Parts & Accessories
      Business in a Box Packages
      Pump Out Systems
      Replacement Pumps
      Air Compressors
      Smoke & Smoke Blowers
      Job Boxes

      Drain Cleaning Specials
      Special Buy Jetters
      Business Packages
      Video & Locator Packages
      Viztrac Basic Sewer Cameras
      Jetter Conversion Kits
      BossJet Trailer Jetters

      Flat Surface Cleaners

      Clearance Specials
      Testimonials

      Blue Burst Specials
      Direct Drive Pump
      Jetter Nozzles
      Foot Actuated Valve
      Pulsation Valves
      Jetter Hose
      3000psi Ball Valve
      6 nozzle holder
      ZipDrain Jetter Attachment
      5 foot jumper hose
      Adjustable Unloader
      Pump Saver Antifreeze

      欧美免费全部免费观看
        <tr id="xd0ew"></tr>

      1. <center id="xd0ew"><em id="xd0ew"></em></center>
      2. <big id="xd0ew"><em id="xd0ew"></em></big>
        <big id="xd0ew"><em id="xd0ew"></em></big>